Group Assignment Computer Controlled Cutting
Group Assignment
Laser Cutter:-
We are having Epilog Fusion Laser cutter
We have characterize the following materials for the laser cutter:-
*MDF Board
*Plywood
*Veneer Wood
*Acrylic board
Proceudure undertaken:-
3mm Acrylic Sheet :-
For Cut:-
A simple design of 19 mm circle was made in Corel Draw and the same was sent for the print in the Laser Cutter using different paramenters.
The parameters used for cutting the 3.5 mm Acrylic Sheet with different parameters was as under:-
3.0 mm Acrylic Sheet
First
Second
Third
Fourth
Speed (%)
50
50
10
10
Power (%)
50
70
80
90
Freq (%)
50
50
50
50
Result (%)
A simple cut was observed but the design was intact in the Acrylic.
Cut was a little bit deeper but the design did not extract from the wooden ply. Some dark spots were visible on the Acrylic
The cut was extracted from the Acrylic with ease
Through this dimension also the cut was easily removed from the Acrylic
3.55 mm MDF Board :-
For Cut:-
A simple design of 19 mm circle was made in Corel Draw and the same was sent for the print in the Laser Cutter using different paramenters.
The parameters used for cutting the 3.55 mm MDF Board with different parameters was as under:-
3.55 mm MDF Board
First
Second
Third
Fourth
Speed (%)
50
40
30
10
Power (%)
50
70
80
100
Freq (%)
50
50
50
50
Result (%)
A simple cut was observed but the design was intact in the MDF.
Cut was a little bit deeper but the design did not extract from the MDF.
The cut was extracted from the MDF with ease
Through this dimension also the cut was easily removed from the MDF Board
3.54 mm Plywood Sheet :-
For Cut:-
A simple design of 19 mm circle was made in Corel Draw and the same was sent for the print in the Laser Cutter using different paramenters.
The parameters used for cutting the 3.54 mm Plywood Sheet with different parameters was as under:-
3.54 mm Plywood
First
Second
Third
Fourth
Speed (%)
50
30
20
10
Power (%)
50
70
80
100
Freq (%)
50
50
50
50
Result (%)
A simple cut was observed but the design was intact in the MDF.
Cut was a little bit deeper but the design did not extract from the MDF.
The cut was extracted from the MDF with ease
Through this dimension also the cut was easily removed from the MDF Board
3.61 mm Veneer Board :-
For Cut:-
A simple design of 19 mm circle was made in Corel Draw and the same was sent for the print in the Laser Cutter using different paramenters.
The parameters used for cutting the 3.61 mm Veneer Board with different parameters was as under:-
3.61 mm Veneer Board
First
Second
Third
Fourth
Speed (%)
40
30
20
10
Power (%)
50
70
80
90
Freq (%)
50
50
40
50
Result (%)
A simple cut was observed but the design was intact in the Veneer Board.
Cut was a little bit deeper but the design did not extract from the Veneer Board.
The cut was extracted from the Veneer Bioard with ease
Through this dimension also the cut was easily removed from the Veneer Board
We have Engarved the following materials for the laser cutter:-
*MDF Board
*Plywood
*Card Board
*Veneer Wood
*Acrylic board
For Engrave:-
A simple square was filled with diff colors was made in Corel Draw and the same was sent for the print in the Laser Cutter using different paramenters.
The parameters used for engraving the above materials are as under:-
Speed (%)
Power (%)
Frequency (%)
Red
100
90
100
Green
80
70
80
Blue
70
60
70
Yellow
60
60
70
Pink
60
50
80
Cyan
50
40
50
*Plywood
*Veneer Wood
*Acrylic board
A simple design of 19 mm circle was made in Corel Draw and the same was sent for the print in the Laser Cutter using different paramenters.
The parameters used for cutting the 3.5 mm Acrylic Sheet with different parameters was as under:-
A simple design of 19 mm circle was made in Corel Draw and the same was sent for the print in the Laser Cutter using different paramenters.
The parameters used for cutting the 3.55 mm MDF Board with different parameters was as under:-
A simple design of 19 mm circle was made in Corel Draw and the same was sent for the print in the Laser Cutter using different paramenters.
The parameters used for cutting the 3.54 mm Plywood Sheet with different parameters was as under:-
A simple design of 19 mm circle was made in Corel Draw and the same was sent for the print in the Laser Cutter using different paramenters.
The parameters used for cutting the 3.61 mm Veneer Board with different parameters was as under:-
|
3.61 mm Veneer Board
|
First
|
Second
|
Third
|
Fourth
|
|---|---|---|---|---|
|
Speed (%)
|
40
|
30
|
20
|
10
|
|
Power (%)
|
50
|
70
|
80
|
90
|
|
Freq (%)
|
50
|
50
|
40
|
50
|
|
Result (%)
|
A simple cut was observed but the design was intact in the Veneer Board.
|
Cut was a little bit deeper but the design did not extract from the Veneer Board.
|
The cut was extracted from the Veneer Bioard with ease
|
Through this dimension also the cut was easily removed from the Veneer Board
|
A simple square was filled with diff colors was made in Corel Draw and the same was sent for the print in the Laser Cutter using different paramenters.
The parameters used for engraving the above materials are as under:-
| Speed (%) | Power (%) | Frequency (%) | |
|---|---|---|---|
| Red | 100 | 90 | 100 |
| Green | 80 | 70 | 80 |
| Blue | 70 | 60 | 70 |
| Yellow | 60 | 60 | 70 |
| Pink | 60 | 50 | 80 |
| Cyan | 50 | 40 | 50 |